We have several antennas for receiving all types of signals.
Aaronia HyperLog 7040.
Description: broadband directional antenna, 700 MHz – 4 GHz.
• Only a single broadband antenna is needed for the entire frequency range from 700MHz to 4GHz
• Ideal for EMC measurements with a spectrum analyzer
• High-quality radome with a modern, attractive design
• Polarization levels can be adjusted as desired
• Calibration data can optionally be stored in the antenna and read by IC
• Excellent front-to-back ratio
• Excellently symmetrical radiation patterns
• Integrated 1/4″ tripod mount
• Suitable for mobile use
• Suitable for outdoor installation
• Directional
• Rugged design
• Splash-resistant
• Low weight and small dimensions
• Made in Germany.
LB-159-10-C-SF Standard Gain Horn Antenna.
Operates from 4.9 to 7.05 GHz with a nominal gain of 10 dB and a VSWR below 1.25:1 with a female SMA connector output. The LB-159-10-C-SF model has uniform gain across its entire frequency range, which provides efficient directivity and performance characteristics. It can handle 50 W continuously and a peak power of 3000 W. Built from lightweight, corrosion-resistant aluminum, the antenna will provide years of trouble-free indoor and outdoor service. This standard gain horn antenna is linearly polarized and is ideal for EMI testing, direction finding, surveillance, antenna pattern and gain measurements, and other applications.
ELECTRICAL SPECIFICATION
Frequency, minimum (GHz) 4.9
Frequency, maximum (GHz) 7.05
Waveguide type: rectangular
EIA WR waveguide size: WR159
Gain, typical (dBi) 10
Polarization: linear
3 dB beamwidth, E-plane, typical (degrees) 55
3 dB beamwidth, H-plane, typical (degrees) 50
Cross-pol. isolation, typical (dB) 35
VSWR, typical 1.25:1
Impedance, (Ohms) 50
Power handling, CW, (W) 50
Power handling, peak, (W) 3000
INTERFACE
Coaxial output type
SMA connector
Connector gender: Female
MECHANICAL SPECIFICATION
Figure type C
Body material: Aluminum
Finish: Chemical conversion coating, gray paint
Size, width (mm) 81
Size, height (mm) 61.9
Size, length (mm) 175
Weight, (kg) 0.4.
HT6 600MHz to 10GHz UWB Antenna.
Log-periodic antenna, EMC antenna for spectrum analyzer.
Description:
The HT6 directional passive log-periodic antenna has a gain of up to 6 dB. It is designed for radio frequency measurements (measuring field strength and the peak direction (amplitude) of the electromagnetic radiation source).
It operates in the frequency range of 600MHz to 10000MHz. The antenna’s wide operating range allows signal levels to be measured for all common technologies and standards. These include:
* 2G (EDGE, GPRS on GSM 900 and GSM 1800)
* 3G (900 UMTS and 2100 UMTS)
* 4G (LTE 800, LTE 1800 and LTE 2600) and YOTA
* WI-FI 2400 (IEEE 802.11 b/g/n)
The antenna has adjustable gain across the operating frequency range. We recommend using a spectrum analyzer to survey the electromagnetic environment. The package includes a cable to connect a spectrum analyzer or other receiving device.
Exquisite, unique design: the HT6 antenna can be used with the SA6 spectrum analyzer for easy field use.
With the help of a measurement antenna it can be used for:
* Power flux density measurement.
* RF environmental analysis
* Pointing the antenna at the base station.
* Probing the source of the signal or interference.
* Analysis of the operating parameters of boosters and repeaters.
* Creating an electromagnetic field with a given density.
* Measurement of various types of antenna parameters.
* Measurement of electromagnetic compatibility parameters of radio-electronic equipment.
* Monitoring of the electromagnetic environment
* Direction finding of sources of electromagnetic radiation.
Specifications:
* Antenna size: 400 x 185 x 20 mm/15.7 x 7.3 x 0.8″
* Operating frequency: 600MHz-10000MHz (600MHz-10GHz)
* Antenna gain: 1dB to 6dB
* VSWR at operating frequency: no more than 2.2
* Polarization: linear
* Input impedance: 50 ohms
* Connector: SMA female thread
* Product weight: 140 g/0.3 lb
640MHz – 9.2 GHz RHCP Right-Hand Circularly Polarized Antenna.
UWB spiral antenna with SMA female connector
Description:
– This antenna is an ultra-wideband equiangular spiral circularly polarized antenna, available in left-hand circularly polarized and right-hand circularly polarized versions.
– It can be used for direction finding, spectrum analysis, signal analysis, navigation positioning, broadband measurement, etc., providing a circularly polarized directional gain of 4 to 7 dBi in the frequency range of 700 MHz to 9.2 GHz.
– It is used for typical operating frequencies of 915 MHz, 1090 MHz ADS-B, 1268 MHz-1610 MHz GPS, 1420 MHz, 2.4 GHz, 5.8 GHz VTX with low standing wave ratio, high gain and significant performance.
Specification:
– Working bandwidth: 640 MHz – 9.2 GHz
– Polarization method: right-hand polarization
– Gain: 4dBi – 7dBi
– Radiation angle: H = E = 84°
– Axial ratio: <1dB
– Impedance: 50 ohms
– VSWR: < 1.5
– Diameter: 150 mm.
WS3940-ULD GPS + Cellular
Combined integrated antenna
Applications:
¨ Covert installation, cellular + GPS law enforcement
¨ Automotive navigation OEM
¨ Fleet management and telematics OEM
¨ Asset tracking systems
Dimensions: (in inches)
Custom-built for the telematics market, the WS3940-ULD Cellular + GPS integrated antenna is an
excellent choice for systems that require reliable, highly accurate positioning data as well as clear,
consistent communications between the host and the vehicle. With excellent LHCP rejection for fewer multipath effects and a low-noise amplifier, the antenna provides a clear, consistent GPS signal. On Cellular, reception is tuned to receive 824 -894 MHz (cellular), 890-960 MHz (GSM), 1710-1880 MHz (European), and 1850-1990 MHz (North American) frequencies for optimal system performance.
Features:
¨ Quad-band cellular reception
¨ Semi-flexible for covert installation
¨ Excellent out-of-band signal rejection
¨ High-gain active GPS antenna
¨ Wide range of connector types available.
3-meter cable
(Standard)
WS3940-ULD GPS + Cellular
Combined integrated antenna
With a high-performance custom-designed
GPS patch element and a quad-band cellular
antenna in an ultra-thin design. The WS3940-
ULD’s compact, efficient design combines
the power of GPS and cellular technologies within a single antenna, thereby maximizing your installation options. With a wide range of connector types, the WS3940-ULD is the perfect solution for TELEMATICS devices and covert installations.
Technical specifications
Environmental specifications
¨ Operating temperature: -40 °C to +80 °C
¨ Humidity: 95% max. (non-condensing) Mechanical
¨ Dimension: 5.0” x 2.07” x 0.33”
¨ High-density Poron foam backing
¨ Cable: Shikoku DUAL 1.5 DS-QEHV cable
¨ Cable length: 3 Meters (Standard), other lengths optional
¨ Cable loss: 1.0 dB/m typical
¨ Connector: SMA standard, other connectors available.
Antenna response (GPS)
¨ Frequency: 1575.42 MHz
¨ Gain (typical): 25 dB
¨ Noise figure (typical): 1.6 dB
¨ Polarization: Right-hand circular
¨ LHCP rejection: > 6 dB
¨ VSWR: 2.0
Electrical (GPS)
¨ Voltage: 2.7 – 5.0 VDC
¨ Current (typical): 8.0 mA
Electrical (Cellular)
¨ Frequencies: 824-894 MHz (Cellular)
890-960MHz (GSM)
1710-1880 MHz (Europe)
1850-1990 MHz (North America)
¨ Output impedance: 50 ohms nominal
¨ VSWR: 2.0
¨ Gain: 2 dBi (approx.)
